The Alarms & Events Reason is claimed to describe the reason behind an event. Reason is mapped to OPC EventCategory. OPC EventCategory is more intended to describe the contents of an event rather than the reason causing the event. Investigate if this shall cause a name change of Reason to EventCategory. This will simplify mapping DAIS A&E to OPC A&E.

Change as suggested in section Changes to formal/02-11-07

A new datatype that corresponds to OPC VT_EMPTY is needed to indicate that the server shall use the native data type. SimpleValueType needs a UNSPECIFIED_TYPE

Change as suggested

Bad parameters are signaled with the error code E_INVALIDARG. The corresponding OMG exception is BAD_PARAM. Remove InvalidStateSpecified in E&A Subscription and use BAD_PARAM instead

Changed according to suggestion

When describing: DAIS::DataAccess::GroupEntry::Manager::create_entries() last paragraph on page 4-38 says:

"both item and pathname specified ->..."

I think that there is no way to specify both itemID and pathname in this method. Paramethers passed in this method are:

DAIS::DataAccess::GroupEntry::Description

where for item identification we use union, described on page 3-3,3-6:

DAIS::ServerItemIdentification

So, how we can specify both item ID and pathname?

Update the text to reflect the IDL

The SimpleIO need an own error report struct as it can't use the handles in the ItemError struct. Suggestion
struct ItemError

;

Change as suggested

User quality is currently a unsigned short. This is insufficient and shall be increased to a long

Refer to dtc/2004-10-05 section 3.1.

The methods enable_conditions() and disable_conditions() at the
Source::Home and Area::Home does not return error codes for Sources or
Areas that fails.

Refer to dtc/2004-10-05 sections 5.2.5.2 and 5.2.6.2

find_by_type currently takes a single root node as input. By changing this to a sequence it is possible to use a set of nodes from a previous call as input to a subsequent call

see above, rejected

OPC_QUALITY_EGU_EXCEEDED twice in table describing detailed quality flags for uncertain quality. Remove one entry.

Change as suggested

Exception InvalidFilter is missing in find_by_parent() and find_by_type() in section 3.1.7.2.

Add the exception

In description of Item::Home the interface is called ItemHome, shall be just Home

Change as suggested

Description of simple_io_home is missing in section 4.2.2.2

rejected The description is not missing. This is not an issue.

When an A&E subscription has a non-zero keep-alive time, the server will
insure that the client receives a callback on the subscription minimally at
rate indicated by the keep-alive time, even when there are no new events to
report. By providing callbacks at a minimum known frequency, the client can
be assured of the health of the server and subscription without resorting
to "pinging the server" (the common practice of making periodic calls to a
server method, e.g. IOPCEventServer::GetStatus() ).

Add a new member keep_alive_time in the AlarmsAndEvents::Subscription::State struct

The DAIS specification states that validate_entries (on DAISGroupEntry) is: "Used to check if Descriptions a client holds are still valid without effecting the existing group." The OPC specification of ValidateItems (on IOPCItemMgt) states: "Determines if an item is valid (could it be added without error). Also returns information about the item such as canonical datatype. Does not affect the group in any way."
Update the specification to reflect the behavior according to the OPC specification

Change as suggested

When describing DAIS::DataAccess::Item::Home::get_ids() the specification says:

"Translate a sequence of pathnames to the corresponding sequence of >>node<< identifications. If a pathname fails to translate to >>node<< identification..."

I suppose that word >>node<< should be replaced with >>item<< because: 1) the IDL definition for this method is: ItemIDs get_ids(in Strings pathnames); 2) description of return values on page 4-22 says: "return The corresponding sequence of >>item<< identifications."

Changed according to suggestion

In this idl-file is defined datatype TypeID. But CORBA 3 was define keyword - typeid.

In result idl compiler write:

tao_idl: "DAISCommon.idl", line 15: spelling differs from IDL keyword only in case: "TypeID" tao_idl: "DAISCommon.idl", line 20: spelling differs from IDL keyword only in case: "TypeID"

To avoid keyword collision in CORBA 3 the existing type ResourceID replaces TypeID

Regarding the specification "IDL for Data Acquisition from Industrial Systems": The IDL files define interfaces named Home, which clash with the keyword "home" of the CORBA 3 specification.

The TAO IDL compiler reports: tao_idl: "DAISNode.idl", line 33: spelling differs from IDL keyword only in case: "Home"

"Home" interfaces are renamed to "IHome" the distinguish from the keyword Home

When describing what DAIS::DataAccess::Item::ItemHome::find_each() returns, the specification says:

"return: An >>iterator<< holding the item descriptions"

I suppose that word >>iterator<< should be replaced with >>sequence<< since the IDL definition is:

Descriptions find_each(in ItemIDs items) raises (UnknownItemID);

Changed according to suggestion

In DAFDescriptions.idl file: - The use of anonymous sequences are deprecated. Errors occur during compilation